BETA Build 18 (v3.6.0)
Release Date: 2008-11-12
Download

RED ONE Build 18 (BETA) v3.6.0 Nov 12, 2008

SUMMARY:

Build 18 adds native 2x anamorphic recording at 4K 1 – 25 fps, 3K 1- 50 fps and 2K 1 – 100 fps with REDCODE 36 image quality to a RED 8 GB CF card. In addition, all monitor outputs including RED-EVF, RED-LCD, HDMI and HD-SDI, preview and playback recorded images in a final presentation equivalent 2.40:1 aspect ratio.

A companion version of RED-ALERT (v3.6.0) that scales and expands anamorphic .R3D footage is also available from the RED support web site.

The existing QuickTime codec will play camera generated QuickTime Reference Movies of anamorphic .R3D footage in the original 1.2:1 aspect ratio.

Note: RED does not recommend using Build 18 on commercial jobs until formal release of the firmware at the conclusion of beta test cycles.

Note: After upgrading to Build 18, on-camera playback of media recorded by earlier builds may not be possible, nor can you add additional clips to digital media formatted under an earlier build. Ensure you reformat any digital media before shooting under Build 18.

Note: Make sure that you download the latest versions of the post production software (use V3.6.0 version of RED Alert post production software to process Build 18 footage 4K / 3K / 2K ANA footage) available at www.red.com/support before processing Build 18 footage.

Installation Instructions for RED ONE Build 18 v3.6.0 camera firmware:

• This upgrade is fully contained in the folder " build_18_v3.6.0 "

• In that folder is a copy of this Read Me file and the folder named " upgrade "

• The " upgrade " folder includes the camera firmware upgrade file " redone.su "

• DO NOT rename this folder, the camera only opens a folder named " upgrade "

• Do NOT decompress the " redone.su " file, the camera will perform that task.

• Format a CF card using Build 17

• Connect the CF card to your P.C or Macintosh via a CF card reader.

• Copy the folder called " upgrade " onto the CF card.

• Unmount the CF card from your computer (drag to the trash can)

• Ensure your camera is powered down.

• Insert the CF card into the CF card slot of your RED-ONE camera.

• Power up the camera.

• After booting up, the camera rear status display will report " New Firmware " and the RED-EVF or RED-LCD will report “A software update is available for your system”
• Press the joystick to confirm, and the rear status display will report " Upgrading "

• During the upgrade process, a blue progress bar will be visible on the RED-EVF or RED-LCD. This bar will continue for the duration of the upgrade, which is approximately five minutes.

• At the end of the upgrade process, the rear status display will report “O.K. Cycle Power” The RED-LCD or RED-LCD will report " Upgrade complete. Power cycle the camera to continue. "

• Power down the camera, wait five seconds, then power up the camera.

• Verify that the camera rear status display and or monitors report back: PIN (value specific to camera) Build 18 Version 3.6.0

• Installation is now complete.

Note: After the firmware upgrade, re-format the CF card prior to recording.

Note: After any camera firmware upgrade, performa a BLACK SHADING calibration.

Significant changes since Build 17.

• Added native anamorphic recording modes (4K / 3K / 2K)

• Added anamorphic frame guides / monitor de-squeeze.

Note: Use V3.6.0 version of RED Alert post production software to process Build 18 4K / 3K / 2K ANA footage, available at www.red.com/support before processing Build 18 footage.

Note: Anamorphic operates with 2x anamorphic lenses. Do not use with 1.3x anamorphic or non-anamorphic lenses.

Operational restrictions of Build 18 series firmware.

• S4/i Lens Data Interface requires corresponding Lens Interface hardware.

• Revised audio PPM metering requires corresponding Revision 2 audio board.

• Non-speed verified CF cards are limited to 2K record resolution.

• Non Build 18 formatted media may report as “INCOMPATIBLE”- if so, reformat to clear.

• Image Magnify is not available during recording or playback at 3K and 4K resolutions.

• Entering and exiting Image Magnify causes a visual disturbance to monitor outputs.

• Time Code / Edge Code values displayed in monitor outputs do not update in real-time.

• 1080p HD-SDI outputs do not support PsF signal formatting option.

• COLOR exposure meter display is inaccurate if VIEW is set to RAW.

• Limited GUI on HD Preview when both RED-EVF and RED-LCD are selected.

• EVF display with blank for approximately 3 seconds when in SYNC refresh mode:
  • when exiting OPEN GATE mode
  • after a change in Project Resolution
  • after exiting MAGNIFY when in 4K resolution
  • after a Varispeed frame rate change

• Cannot import camera LOOK (.RLK) files from RED Alert! or REDCINE.

Copyright © 2008 RED Digital Cinema, All Rights Reserved.

---

BETA Build 17 (v3.4.1)
Release Date: 2008-10-28
Download

RED-ONE Build 17 v3.4.1 OCT 27, 2008

SUMMARY

RAW exposure meter, embedded audio and time code in HD-SDI outputs, 4K HD recording mode (3840 × 2160 pixels), support for RED 16GB CF cards and RED-RAM 64GB flash drive, enhanced Timecode and Genlock functionality, USER 5 Key (located on RED-LCD), GPI trigger functions – Pre-Record, Shut Down, Play Clip, Next Clip, USER KEY functions – Ramp, Timelapse, Record, ability to disable GUI elements, CLEAR LOOK function, camera firmware support for RED lens S4/i interface, user programmable Safe Action / Title, 1:1 native sensor image magnify, User Preference file, Battery Cycle count.

Note: RED does not recommend using Build 17 on commercial jobs until formal release of the firmware at the conclusion of beta test cycles.

Note: After upgrading to Build 17, on-camera playback of media recorded by earlier builds may not be possible, nor can you add additional clips to digital media formatted under an earlier build. Ensure you reformat any digital media before shooting under Build 17.

Note: Make sure that you download the latest versions of the post production software applications available at www.red.com/support

Installation Instructions for RED-ONE Build 17 v3.4.1 camera firmware.

• This upgrade is fully contained in the folder " build_17_v3.4.1 "

• In that folder is a copy of this Read Me file and the folder named " upgrade "

• The " upgrade " folder includes the camera firmware upgrade file " redone.su "

• DO NOT rename this folder, the camera only opens a folder named " upgrade "

• Do NOT decompress the " redone.su " file, the camera will perform that task.

• Format a CF card using Build 16

• Connect the CF card to your P.C or Macintosh via a CF card reader.

• Copy the folder called " upgrade " onto the CF card.

• Unmount the CF card from your computer (drag to the trash can)

• Ensure your camera is powered down.

• Insert the CF card into the CF card slot of your RED-ONE camera.

• Power up the camera.

• After booting up, the camera rear status display will report " New Firmware " and the RED-EVF or RED-LCD will report “A software update is available for your system”
• Press the joystick to confirm, and the rear status display will report " Upgrading "

• During the upgrade process, a blue progress bar will be visible on the RED-EVF or RED-LCD. This bar will continue for the duration of the upgrade, which is approximately five minutes.

• At the end of the upgrade process, the rear status display will report “O.K. Cycle Power” The RED-LCD or RED-LCD will report " Upgrade complete. Power cycle the camera to continue. "

• Power down the camera, wait five seconds, then power up the camera.

• Verify that the camera rear status display and or monitors report back -

PIN (value specific to camera) Build 17 Version 3.4.1

• Installation is now complete.

Note: After the firmware upgrade, re-format the CF card prior to recording.

Note: After any camera firmware upgrade, performa a BLACK SHADING calibration.

Significant changes since Build 17 v.3.3.9

• Completed optimization for RED 16GB CF cards.

• Addition of embedded time code in HD-SDI outputs.

• Addition of CROSS JAM (creation of 23.98 fps from 29.97 timecode)

• Addition of CROSS GEN (creation of 29.97 fps from 23.98 timecode)

• Added USER KEY function – Record

• Changed method of writing camera LOG file – access via SETUP menu.

• Changed location of PRE-RECORD – access via MEDIA menu.

• Selection of lens Distance data reporting in Feet or Meters

• Addition of Audio LINE input gain control 0dB / 10 dB.

• FALSE COLOR exposure meter tracks VIEW selection – REC709 / REDspace

• Corrected operation of Shutter PHASE control.

• Added USER programmable Safe Action / Title guides.

• Changed MAGNIFY to display 1:1 native sensor resolution.

• Added selection to playback clips using CLIP or CAMERA LOOK values.

• Added USER PREFERENCE file.

Significant changes since Build 16.

• Addition of RAW exposure meter.

• Addition of 4K HD recording mode (3840 × 2160 pixels).

• Support for RED 16GB CF cards and RED-RAM 64GB flash drive.

• Addition of MAX checkbox to CONFIGURE / NEW PROJECT menu.

• Note: Enable MAX for maximum image quality, disable MAX for faster decode times for 4K footage.

• Added Timecode Output enable checkbox: enables Time Code on LEMO 5-pin connector.

• Addition of embedded time code in HD-SDI outputs.

• Addition of embedded audio in HD-SDI outputs.

• Addition of CROSS JAM (creation of 23.98 fps from 29.97 timecode)

• Addition of CROSS GEN (creation of 29.97 fps from 23.98 timecode)

• Improved JAM SYNC operation: removed requirement to record before syncing.

• Genlock (Tri-Level Sync) available when operating with OPEN GATE.

• Change of name for Sensitivity parameter – ASA (now ISO).

• USER KEY MODE “VIEW RAW” now toggles between VIEW RAW and selected VIEW menu selection.

• Change of name for GPI and USER KEY parameter – BURST → TIMELAPSE.

• Added USER 5 Key (located on RED-LCD).

• Added GPI trigger functions – Pre-Record, Shut Down, Play Clip, Next Clip.

• Added USER KEY functions – Ramp, Timelapse, Record

• Added CLEAR LOOK function.

• Added ability to disable GUI elements – EVF menus and Grey Scale defaulted OFF.

• Added ability to defeat EVF menu controls when EVF menu display is set to OFF.

• Changed method of writing camera LOG file – access via SETUP menu.

• Changed location of PRE-RECORD – access via MEDIA menu.

• Added warning screen to advise if media is removed without first Unmounting.

• Non-speed verified CF cards now permitted to record at 2K RAW resolution.
  • Note: Non-speed verified CF cards is solely at end-user risk.
  • Note: RED makes no representations regarding maximum frame rate or immunity to dropped frames.

• Resolved RED-LCD sometimes tearing in lower 10% of screen with 4K footage.

• Re-sized system error messages from full screen to upper central area of GUI.

• Added flashing “RECORD dot” within GUI to indicate system error.

• Corrected spelling errors in drive format splash screens.

• Resolved intermittent “stuck in POST record” error.

• Resolved 29.97 fps Time Base QuickTime reference file issue with long record times.

• S4/i Lens Data Interface (requires corresponding Lens Interface hardware).

• Allow lens Distance data reporting in Feet or Meters.

• Revised audio PPM metering (requires corresponding Revision 2 audio board).

• Addition of Audio LINE input gain control 0dB / 10 dB.

• FALSE COLOR exposure meter tracks VIEW selection – REC709 / REDspace.

• Added user programmable Safe Action / Title guides.

• Changed MAGNIFY to display 1:1 native sensor resolution.

• Added selection to playback clips using CLIP or CAMERA LOOK values.

• Added USER PREFERENCE file.

• Added Battery Cycle count to camera firmware status panel.

• Corrected operation of Shutter PHASE control.

• Corrected Audio Codec error on clip playback

• Corrected Audio Level adjustment from User Keys.

Operational restrictions of Build 17 series firmware.

• S4/i Lens Data Interface requires corresponding Lens Interface hardware.

• Revised audio PPM metering requires corresponding Revision 2 audio board.

• Non-speed verified CF cards are limited to 2K record resolution.

• Non Build 17 formatted media may report as “INCOMPATIBLE”- reformat to clear.

• Image Magnify is not available during recording at 3K and 4K resolutions.

• Entering and exiting Image Magnify causes a visual disturbance to monitor outputs.

• Time Code / Edge Code values displayed in monitor outputs do not update in real-time.

• 1080p HD-SDI outputs do not support PsF signal formatting option.

• COLOR exposure meter display is inaccurate if VIEW is set to RAW.

• Limited GUI on HD Preview when both RED-EVF and RED-LCD are selected.

• EVF display with blank for approximately 3 seconds when in SYNC refresh mode:
  • when exiting OPEN GATE mode
  • after a change in Project Resolution
  • after exiting MAGNIFY when in 4K resolution
  • after a Varispeed frame rate change

• Cannot import camera LOOK (.RLK) files from RED Alert! or REDCINE.

Copyright © 2008 RED Digital Cinema, All Rights Reserved.

---

BETA Build 16 (v3.2.4)
Release Date: 2008-07-22
Download

Build 16, RED ONE camera BETA firmware v3.2.4, July 22, 2008

SUMMARY

Updated .R3D file format, Digital Signal Processing optimization, Image Compression Optimization, addition of REDspace and RAW view modes, high contrast scene codec error mitigation, audio polarity and video sync correction, LCD image tearing reduction, Pre-Record Mode, support for 16GB CF cards, support for 1080p 4:2:2 and RGB 4:4:4 playback of REDCODE RAW .R3D files, User Programmable Keys, RED-EVF menus, Time Code output on LEMO 5 pin timecode connector, Tonal Response Curve, editable LOOK files names, video visible during boot up sequence.

Note: RED does not recommend using Build 16 on commercial productions until the formal release of this firmware at the conclusion of the beta test cycles.

Note: After upgrading to Build 16, on-camera playback of media recorded by earlier builds may not be possible, nor can you add additional clips to digital media formatted under an earlier build. Ensure you reformat any digital media before shooting under Build 16.

Note: Use the latest versions of RED QuickTime Codec, RED Alert! and REDCINE available from www.red.com/support

Note: Recordings made with Build 16 are not supported by current versions of RED Log and Transfer, or 3rd party editing or image processing applications that do not utilize the updated RED QuickTime Codec.

Installation Instructions for RED-ONE Beta Build 16 v3.2.4 camera firmware.

• This upgrade is fully contained in the folder " build_16_v3.2.4 "

• In that folder is a copy of this Read Me file and the folder named " upgrade "

• The " upgrade " folder includes the camera firmware upgrade file " redone.su "

• DO NOT rename this folder, the camera only opens a folder named " upgrade "

• Do NOT decompress the " redone.su " file, the camera will perform that task.

• Format a CF card using Build 15 v2.2.8 (or an earlier version of Build 16)

• Connect the CF card to your P.C or Macintosh via a CF card reader.

• Copy the folder called " upgrade " onto the CF card.

• Unmount the CF card from your computer (drag to the trash can)

• Ensure your camera is powered down.

• Insert the CF card into the CF card slot of your RED-ONE camera.

• Power up the camera.

• After booting up, the camera rear status display will report " New Firmware " and the RED-EVF or RED-LCD will report “A software update is available for your system”
• Press the joystick to confirm, and the rear status display will report " Upgrading "

• During the upgrade process, a blue progress bar will be visible on the RED-EVF or RED-LCD. This bar will continue for the duration of the upgrade, which is approximately five minutes.

• At the end of the upgrade process, the rear status display will report “O.K. Cycle Power” The RED-LCD or RED-LCD will report " Upgrade complete. Power cycle the camera to continue. "

• Power down the camera, wait five seconds, then power up the camera.

• Verify that the camera rear status display and or monitors report back -

PIN (value specific to camera) Build 16 Version 3.2.4

• Installation is now complete.

Note: After the firmware upgrade, re-format the CF card prior to recording.

Note: After any camera firmware upgrade, performa a BLACK SHADING calibration.

Significant changes since Build 15.

• New .R3D file format – compatible with updated QuickTime Codec, RED ALERT.

• Digital Signal Processing optimization.

• Image Compression Optimization.

• Support for 4K 16:9 recordings in REDALERT and QuickTime based applications.

• Support for RED 16GB CF cards.

• Fixed high detail scene codec errors in 4K 16:9 recordings.

• Fixed polarity of audio recording relative to MIC and / or LINE inputs.

• Improved audio sample to video frame synchronization (lip sync accuracy).

• Reduced RED-LCD display tearing on last few lines in 4K record / playback.

• Addition of REDspace and RAW viewing modes.

• Updated file name structure to eliminate duplicate file names.

• Addition of Pre-Record (10 sec or 30 sec loop) mode.

• In-camera 1080p playback of REDCODE RAW 4K / 3K / 2K .R3D files.

• Time Code output enabled on the LEMO 5 pin timecode connector.

• Improved display precision and color response of RED-EVF and RED-LCD.

• Addition of MONO mode Histogram.

• Improved accuracy of RGB Histogram display.

• Changed default Color Temp to be 5600K

• Seperation of Sensitivity (ASA) and Exposure (Compensation) parameters.

• Extended exposure times of up to 1/2 sec enabled in TIMELAPSE menu.

• Addition of Burst record mode in Timelapse menu.

• Added RED-EVF control over Audio, Shutter, ISO and Varispeed parameters.

• Changed COLOR exposure meter to reflect REDspace monitoring as default.

• Added programmable Tonal Response Curves menu.

• Support for P.C editing of file names of camera LOOK files.

• Support for Gray Scale to look around area of GUI.

• Look Around available on HD PREVIEW outputs when LCD and EVF are active.

• Improved video Genlock (Tri-Level Sync) lock for 23.98, 24.00, 25.00, 29.97.

• Added 1.85 and 2.40 Safe Action and Safe Title Protection Guides.

• Improved indiction of image magnify mode with new “X” cursor

• User programmability of A, B, C keys and USER 1, 2, 3, 4, 5 Keys

• Return to last menu position before exiting menus, when UNDO-SYSTEM is pressed

• Changed project FRAME RATE label to TIME BASE.

• Disabled auto-reset of reel counter on change of project time base.

• Added RESET # (manual reset of reel counter) in MEDIA menu.

• Changed FORCE REEL label to CHANGE # and relocated it to MEDIA menu.

• Decreased boot up time, and video is now visible during boot up sequence.

• No roll-back of camera firmware permitted to Build 15 or earlier.

Changes since RED-ONE Beta Build 16 v3.2.1 firmware.

• Additional codec optimization

• Boot up logo relocated to bottom of screen.

• Time Code output enabled on the LEMO 5 pin timecode connector.

Note: Build 16 v3.2.4 requires download of the latest versions of QuickTime Codec, RED Alert! and REDCINE available at www.red.com/support.

Operational restrictions of Build 16 series firmware.

• If using a 16GB CF card, the upgrade file is not erased at the end of the upgrade process.
  Therefore reformatted any 16GB CF cards used for camera firmware upgrades before recording.

• On power up, monitors may display Blue channel only – if so power cycle.

• LCD tearing may sometimes be visible in lower 10% of screen with 4K footage.

• Genlock (Tri-Level Sync) for 50.00 fps has not yet been verified.

• Non Build 16 formatted media will report “DISK INCOMPATIBLE”- reformat to clear.

• Image Magnify is not available during recording at 4K resolutions.

• Edge Code not available from LEMO 5 timecode connector.

• Audio and Timecode are not embedded on HD-SDI outputs.

• 1080p HD-SDI outputs do not support PsF signal formatting option.

• COLOR exposure meter only operates accurately when in VIEW REDspace

• Limited GUI on HD Preview when both RED-EVF and RED-LCD are selected.

• EVF display with blank for approximately 3 seconds when in SYNC refresh mode:
  • when exiting OPEN GATE mode
  • after a change in Project Resolution
  • after exiting MAGNIFY when in 4K resolution
  • after a Varispeed frame rate change

• When in OPEN GATE mode, Genlock (Tri-Level Sync) is not available.

• Cannot exchange camera LOOK (.RLK) files with RED Alert! or REDCINE.

Copyright © 2008 RED Digital Cinema, All Rights Reserved.

---

BETA Build 15 (v2.2.1)
Release Date: 2008-04-02
Download

Build 15, RED ONE camera firmware v2.2.1 Apr 02, 2008

REDCODE 36 Quality setting, 3K 2:1 and 16:9 record resolution, Audio playback, Simultaneous RED-EVF, RED-LCD and HD-SDI/HDMI outputs, Shutter speed reporting in Degrees or 1/xx Sec format, Increased frame rate for 2K recording modes, Anamorphic 2:1 recording modes, Camera LOOK file export/import, Addition of root directory (.RDM) to digital media, Streamlined media formatting and Black Shading algorithms. False Color Focus meter

Installation Instructions for Build 15, RED ONE camera firmware v2.2.1

• Click on the 2.2.1 firmware download link at www.red.com/support web site

• Verify the folder " build_15_red_one_v2.2.1 " appears on your desktop

• Follow the instructions contained in the " build_15_red_one_v2.2.1_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (value specific to camera) Build 15 Version 2.2.1

• Installation is now complete.

Note: After upgrading a BLACK SHADING calibration should be performed. Ensure the lens cap is in place and a formatted CF card is installed before starting a BLACK SHADING operation. Detailed instructions are contained in the Operations Guide.

Significant changes since Build 13.

• Addition of RECODE 36 Compression Quality Setting.

• Addition of 3K and 3K 2:1 record modes.

• On-camera audio playback (headphone, mini-XLR and HDMI)

• Increased frame rate (100+fps) for 2K recording modes.

• 2:1 lens Anamorphic (ANA) recording modes for 2K, 3K, 4K

• Support for simultaneous RED-EVF, RED-LCD and HD-SDI/HDMI outputs.

• MONITOR / ACTIVE parameter replaced by MONITOR / PREVIEW parameter

• Addition of Relative Shutter Speed control

• Shutter speed reporting in Degrees or 1/xx Sec format.

• Improved Shutter speed / angle reporting in SYNCRO and RELATIVE modes

• Shutter speed / angle outside requested value indicator.

• Enhancement of Frame Rate Ramping control.

• Varispeed settings remembered across power cycle

• Enhancement of Histograms to logarithmic based display.

• False Color Focus indicator (red edge highlight over monochrome)

• Camera LOOK file export/import to SD Card.

• Addition of root directory (.RDM) to digital media.

• Addition of full size _F QuickTime Reference Movie

• Adjusted QuickTime file so audio displays as discreet channels

• Streamlined media formatting algorithms.

• Rejection of unqualified media

• Enhanced Black Shading routine.

• Improved RED-DRIVE data synchronization

• Updated RED-EVF color and gamma calibration

• Changed EVF default to Dark Detail ON

• Change of fan default to AUTO (SILENT in record, otherwise VARIABLE)

• Resolution of D.C offset in audio recordings

• Change of Headphone level default to -6dB.

• User activation (re-activation) of +48V Phantom Power on power cycle. Note: Use of +48VPhantom Power not recommended unless using the new RED XLR-to-mini-XLR cable adaptor (single cable with integrated adaptor). Use of XLR-to-mini-XLR adaptor and mini-XLR-to-mini-XLR cable (an adaptor and a cable) should NOT be used. If you need this new XLR-to-mini-XLR cable adaptor, please contact RED for a replacement.

• Removal of User Guides A B C D

• Adjusted GUI to display D.C instead of A.C with 12V power sources.

• Clip Name and starting Timecode in status display on playback.

• Use meter reports in hours rather than minutes.

• Fixed image separation bug when in timelapse record.

Known firmware restrictions for Build 15, RED ONE v2.2.1

• GUI not available on HD PREVIEW outputs if LCD and EVF active.

• Exposure below 1/24th sec not available in TIMELAPSE menu.

• Zoom is not available during record for 4K resolutions.

• Timecode output not enabled on LEMO 5 pin connector.

• Audio and Timecode not present in HD-SDI outputs.

• End user may not edit the filename of a LOOK file.

• May not exchange LOOK files with REDALERT! or REDCINE.

• Audio playback in REDALERT! and REDCINE is not enabled.

• Noise may be present on +48V Phantom Power Output.

• 4K 16:9 recording not supported by REDALERT! or QuickTime applications.

• EVF blanks for 3 seconds exiting OPEN GATE in SYNC refresh mode.

• EVF blanks for 3 seconds after change in Project Resolution in SYNC refresh mode.

• EVF blanks for 3 seconds after exiting MAGNIFY in 4K resolution in SYNC refresh mode.

• EVF may blank for 3 seconds after Varispeed frame rate change in SYNC refresh mode.

• Safe Action / Safe Title not correctly positioned for ANA recordings

• _F QuickTime proxies not fully supported by QuickTime applications.

• 4K 16:9 _F, _H, _M and _P QuickTimes may crash QuickTime Player.

• Dual Link HD-SDI outputs replicate HD PREVIEW or PLAYBACK HD-SDI signal.

Copyright © 2008 RED Digital Cinema, All Rights Reserved.

---

BETA Build 14 (v2.0.3)
Release Date: 2008-02-07
Download

Build 14, RED ONE camera firmware v2.0.3 Feb 07 , 2008

SUMMARY:

Audio Playback, 3K 2:1 and 16:9 Record Resolutions, REDCODE 28 and REDCODE 36 Compression Quality Settings, Focus Overlay, Relative Shutter, Enhancements to Syncro Shutter, Frame Rate Ramping, Histograms.

Installation Instructions for Build 14, RED ONE camera firmware v2.0.3

• Click on the 2.0.3 firmware download link at www.red.com/support web site

• Verify the folder " build_14_red_one_v2.0.3 " appears on your desktop

• Follow the instructions contained in the " build_14_red_one_v2.0.3_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (value specific to camera) Build 14 Version 2.0.3

• Installation is now complete.

Note: Following this firmware upgrade, unless upgrading from Build 12 or 13, a BLACK SHADING calibration MUST be performed. See User Guide for detailed instruction notes.

Significant changes since Build 13.

• Audio playback on camera (headphone, mini-XLR and HDMI)

• Addition of 3K and 3K 2:1 record modes.

• Addition of RECODE 36 Compression Quality Setting.

• Addition of full size _F QuickTime Reference Movie.

• Addition of Relative Shutter Speed control.

• Addition of AUTO fan mode (SILENT in record, otherwise VARIABLE)

• Enhancement of Syncro Shutter Speed adjustment control.

• Enhancement of Frame Rate Ramping control.

• Enhancement of Histograms to logarithmic based display.

• Enhancement of Headphone volume controls.

• Changed EVF default to Dark Detail ON

• Temporary removal of +48V Phantom Power mode

• Resolution of D.C offset in audio (relative to Build 14 V2.0.1 / 2.0.2)

Known firmware restrictions for Build 14, RED ONE v2.0.3

• Audio playback in RED-ALERT and RED-CINE is not enabled.

• Changing resolutions with VARISPEED enabled causes image tearing

• Look File menu in place but not enabled for file SAVE / RECALL

• 4K 16:9 recording not yet supported by RED ALERT or by QuickTime Player.

• 4K _F, _H, _M and _P QuickTimes created by camera may crash QuickTime Player.

• RED-LCD plus Preview HD-SDI monitor output simultaneously active not supported.

• RED-EVF, RED-LCD, Preview HD-SDI, HDMI simultaneously active not yet supported.

• Dual Link HD-SDI outputs always replicate 720p PREVIEW or PLAYBACK HD-SDI signal.

• Audio and Timecode not present in HD-SD outputs.

• Use meter reports in minutes rather than hours.

Copyright © 2008 RED Digital Cinema, All Rights Reserved.

---

BETA Build 13 (v1.8.8)
Release Date: 2008-01-18
Download

Build 13, RED ONE camera firmware v1.8.8 Jan 16, 2008

SUMMARY:

Resolution of audio hiss on boot up.

Installation Instructions for Build 13, RED ONE camera firmware v1.8.8

• Click on the 1.8.8 firmware download link at www.red.com/support web site

• Verify the folder " build_12_red_one_v1.8.8 " appears on your desktop

• Follow the instructions contained in the " build_13_red_one_v.1.8.8_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (n/a or value specific to camera) Build 13 Version 1.8.8

• Installation is now complete.

Note: Following this firmware upgrade, a BLACK SHADING calibration MUST be performed. See User Guide for detailed instruction notes.

Significant changes since Build 12

• Resolution of audio hiss on camera boot up.d on request in status display.

Known firmware restrictions for Build 13, version v1.8.8

• 4K 2:1 at 29.97 is not supported with CF Card, only with RED-DRIVE.

• Audio playback on camera is not enabled.

• Audio playback in RED-ALERT and RED-CINE is not enabled.

• No variable gain limiter in headphone output (may sound quiet or clip).

• 4K recording is not yet supported by RED ALERT or by QuickTime Player.

• 4K _H, _M and _P QuickTimes created by camera crash QuickTime Player.

• RED-LCD plus Preview HD-SDI monitor output simultaneously active not supported.

• RED-EVF, RED-LCD, Preview HD-SDI, HDMI simultaneously active not yet supported.

• Dual Link HD-SDI outputs always replicate 720p PREVIEW or PLAYBACK HD-SDI signal.

• Audio and Timecode not present in HD-SDI or HDMI outputs.

• Use meter reports in minutes rather than hours.

• On boot up, n/a being reported as P.I.N number on camera s/n 001 – 100.

Copyright © 2007 RED Digital Cinema, All Rights Reserved.

---

BETA Build 12 (v1.8.6)
Release Date: 2007-12-24
Download

Build 12, RED ONE camera firmware v1.8.6 Dec 24 , 2007

SUMMARY:

Audio Recording and Metering, OPEN GATE mode for RED-EVF, SYNC Mode for RED-EVF, False Color and Zebra on HDMI and PVW HD-SDI, GMT Time and Day with Time Zone offset, Programmable GPIO’s, Interval and Trigger based TimeLapse, Frame Rate Ramping, Black Shading Calibration / Highlight Streak Suppression

Note: Unless upgrading from a previous version of Build 12, a BLACK SHADING calibration must be performed. This parameter is located in SYSTEM / MAINTENANCE. Ensure that the lens cap is in place and a formatted CF card is installed before starting a BLACK SHADING operation. More detailed instructions are contained in the System Menus section of the Operations Guide.

Installation Instructions for Build 12, RED ONE camera firmware Beta v1.8.6

• Click on the 1.8.6 firmware download link at www.red.com/support web site

• Verify the folder " build_10_red_one_v1.8.6 " appears on your desktop

• Follow the instructions contained in the " build_11_red_one_v.1.8.6_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (n/a or value specific to camera) Build 12 Version 1.8.6

• Installation is now complete.

Note: Following this firmware upgrade, a BLACK SHADING calibration MUST be performed. See User Guide for detailed instruction notes.

Significant changes since Build 11.

• Audio recording and metering (playback on camera is currently not supported)

• Audio playback via QuickTime Reference Files and QuickTime Player / FCP.

• Addition of OPEN GATE mode for Viewfinder and other Monitor outputs

• Addition of False Color and Zebras to HDMI and PVW HD-SDI outputs.

• Removed SYSTEM/SETUP/RECORD MODE, returned to Checkbox enable for Varispeed

• Interval based TimeLapse.

• Frame rate ramping mode.

• Added GPIO programmability.

• Addition of SET TIME (Hours / Minutes / Seconds) in SETUP menus.

• Addition of TimeZone Offset to (GMT) time and day settings.

• Media directory now formatted as Camera Letter + Reel Number + Date.

• Addition of BACK SHADING (black level calibration) in MAINTENANCE

• Timecode displayed by QuickTime Player with QuickTime Reference movies created by camera at 50.00 and 59.97 fps Project Frame Rates corrected.

• TINT parameter reset to default value (0) on change of Color Temp value.

• Changed default timecode DISPLAY to TIME CODE ( time of day)

• Changed default FAN mode to VARIABLE.

• Deletion of Hours / Minutes / Seconds reset from TIMECODE menu.

• Deletion of 2.35 and 1.85a Frame Guides (2.39 a.k.a 2.40 and 1.85 are guides are available)

Additional significant changes since Build 10

• Addition of 29.97 fps Project Frame Rate for 4K 2:1 record resolution.

• Increased Varispeed range to 1 – 30 fps for 4K 2:1 record resolution.

• Increased data rate of 4K (16:9) recording mode.

• Increased data rate of 2K (16:9) recording mode.

• Addition of GPO tally at completion of STEP RECORD enabled in TIMELAPSE

Additional significant changes since Build 9.

• Support for RED-EVF plus Preview HD-SDI / HDMI output simultaneously active.

• Addition of user selectable Video or Video + GUI monitoring modes on RED-LCD.

• Addition of 2K 2:1 recording mode.

• Addition of 50.00 and 59.94 Project Frame Rates for 2K and 2K 2:1 recording modes.

• Addition of 50 fps / 60 fps selection for HD-SDI outputs (720p/50 or 720p/59.94)

• Addition of GPI trigger enabled TIMELAPSE (one shot) recording.

• Addition of GPI trigger enabled RECORD and GPO external tally output signals.

• Addition of RGB COMPOSITE or LUMINANCE Histogram in default GUI display.

• Addition of RGB Channel Exposure Meter in default GUI display.

• Addition of SPOT EXPOSURE meter in METER selection in VIDEO/AV MENU/VIEWFINDER.

• Addition of DARK DETAIL mode for RED-EVF

• Addition of SYNCED or FIXED refresh rates for RED-EVF in SYSTEM/MONITOR.

• Addition of RECORD MODE parameter (NORMAL / VARISPEED / TIMELAPSE) in SETUP.

• Addition of enable checkbox for USER 1 and USER 2 keys in KEYMAP submenu.

• Addition of VARIABLE fan speed mode to SYSTEM/SETUP/MAINTANCE/FAN.

Additional significant changes since Build 8.

• Playback of recorded clips on camera.

• Cue to beginning of existing clips, step through recorded clip list

• Normal, Fast Forward and Reverse playback.

• Addition of Simple Exposure Meter – indicates clipping in R G B channels

• Enhanced Focus Assist Algorithm with adjustable sample window

• Enhanced False Color Exposure Meter with new Skin Tone indication (Pink band)

• Toggle of METERS ON/OFF by User Key of RED-EVF

• Toggle of COLOR ON/OFF by User Key of RED-EVF

• Simplified VIEWFINDER menu structure.

• Change to project logic. Change of Resolution no longer forces New Project.

• Improved Accuracy of Time Code when not in Jam Sync (external reference) mode

• Fixed Edge Code reporting as 1.00.00.000 on power cycle

• Camera log file created on media unmount

• PIN, Build and Version data reported on request in status display

• Use meter data reported on request in status display

Known firmware restrictions for Build 12, RED ONE v1.8.6

• Audio playback on camera is not enabled

• Audio playback in RED-ALERT and RED-CINE is not enabled.

• No variable gain limiter in headphone output (may sound quiet or clip)

• 4K recording is not yet supported by RED ALERT or by QuickTime Player.

• 4K _H, _M and _P QuickTimes created by camera crash QuickTime Player.

• RED-LCD plus Preview HD-SDI monitor output simultaneously active not supported.

• RED-EVF, RED-LCD, Preview HD-SDI, HDMI simultaneously active not yet supported.

• Dual Link HD-SDI outputs always replicate 720p PREVIEW or PLAYBACK HD-SDI signal.

• Audio and Timecode not present in HD-SDI or HDMI outputs

• RGB Channel Exposure Meter viewed on HDMI monitor has erratic behavior.

• Use meter reports in minutes rather than hours.

• Possibility of n/a being reported as P.I.N number on boot up.

Copyright © 2007 RED Digital Cinema, All Rights Reserved.

---

BETA Build 11 (v1.7.0)
Release Date: 2007-11-30
Download

Build 11, RED ONE camera firmware v1.7.0 Nov 30, 2007

SUMMARY:

Increased data rate for 4K and 2K record resolutions, 29.97 Project Frame Rate for 4K 2:1. 1 – 30 fps Variable Frame Rate for 4K 2:1, Step Record GPO tally for STEP RECORD in Timelapse mode.

Installation Instructions for BETA Build 11, RED ONE camera firmware v1.7.0

• Click on the 1.7.0 firmware download link at www.red.com/support web site

• Verify the folder " build_10_red_one_v1.7.0 " appears on your desktop

• Follow the instructions contained in the " build_11_red_one_v.1.7.0_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (n/a or value specific to camera) Build 11 Version 1.7.0

• Installation is now complete.

Significant changes since Build 10, RED ONE v1.6.4

• Added 29.97 fps Project Frame Rate for 4K 2:1 record resolution.

• Increased Varispeed range to 1 – 30 fps for 4K 2:1 record resolution.

• Increased data rate of 4K (16:9) recording mode.

• Increased data rate of 2K (16:9) recording mode.

• Addition of GPO tally at completion of STEP RECORD enabled in TIMELAPSE

• Change to SYNCED refresh mode as default for RED-EVF.

Known firmware restrictions for Build 11, RED ONE v 1.7.0

• Varispeed recording must first be enabled in SYSTEM/SETUP/RECORD MODE

• Open Gate function in VIDEO/AV MENU/VIEWFINDER is not operational

• INTERVAL (a.k.a CONTINUOUS) mode in Timelapse is not operational

• Timecode displayed by QuickTime Player with QUickTime Reference movies created by camera under 50.00 and 59.97 fps Project Frame Rates incorrect.

• 4K recording is not yet supported by RED ALERT or by QuickTime Player.

• 4K _H, _M and _P QuickTimes created by camera crash QuickTime Player.

• RED-LCD plus Preview HD-SDI monitor output simultaneously active not supported.

• RED-EVF, RED-LCD, Preview HD-SDI, HDMI simultaneously active not yet supported.

• Frame rate ramping is not supported in this release.

• Audio recording, monitoring or playback are not supported in this release.

• Dual Link HD-SDI outputs always replicate 720p PREVIEW or PLAYBACK HD-SDI signal.

• Not all frame guides selectable within each record resolution are enabled.

• RGB Channel Exposure Meter viewed on HDMI monitor may exhibit erratic behavior.

• Cannot reset Hours / Minutes / Seconds in TIMECODE menus.

• Possibility of n/a being reported as P.I.N number on boot up.

Other notes:

• On cameras 1 – 50 the stenciling for the four DIN connectors that provide dual link HD-SDI, Preview HD-SDI and Genlock outputs is incorrect. These should be dual link HD-SDI at the top left / top right, Preview HD-SDI at the lower left and Genlock at the lower right.

• 4K (16:9) recording is enabled in this build, and is supported by REDCINE on both Macintosh OSX and Windows XP platforms. At the time of this software release, 4K QuickTime reference movies created by the camera will crash QuickTime Player and RED ALERT is not compatible with 4K (16:9) recordings. Therefore treat with due caution, especially for commercial jobs.

Copyright © 2007 RED Digital Cinema, All Rights Reserved.

---

BETA Build 10 (v1.6.4)
Release Date: 2007-11-22
Download

Build 10, RED ONE camera firmware v1.6.4 Nov 22, 2007

SUMMARY:

Faster Boot Times. New 2K 2:1 record mode, Increased data rate for 2K record resolutions, new 50.00 and 59.94 Project Frame Rates, simultaneous EVF and PREVIEW / HDMI monitor outputs, Video or Video + Menus switch for RED-LCD, Dropped Frame Meter, RGB Channel Exposure Meter, GPI trigger and GPO tally, preliminary Timelapse mode

Installation Instructions for Build 10, RED ONE camera firmware v1.6.4

• Click on the 1.6.4 firmware download link at www.red.com/support web site

• Verify the folder " build_10_red_one_v1.6.4 " appears on your desktop

• Follow the instructions contained in the " build_10_red_one_v16.4_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (n/a or value specific to camera) Build 10 Version 1.6.4

• Installation is now complete.

Significant changes since Build 9, RED ONE v1.5.1

• Support for RED-EVF plus Preview HD-SDI / HDMI output simultaneously active.

• Addition of user selectable Video or Video + GUI monitoring modes on RED-LCD.

• Addition of 2K 2:1 recording mode.

• Addition of 50.00 and 59.94 Project Frame Rates for 2K and 2K 2:1 recording modes.

• Addition of 50 fps / 60 fps selection for HD-SDI outputs (720p/50 or 720p/59.94)

• Addition of GPI trigger enabled TIMELAPSE (one shot) recording.

• Addition of GPI trigger enabled RECORD and GPO external tally output signals.

• Addition of RGB COMPOSITE or LUMINANCE Histogram in default GUI display.

• Addition of RGB Channel Exposure Meter in default GUI display.

• Addition of SPOT EXPOSURE meter in METER selection in VIDEO/AV MENU/VIEWFINDER.

• Addition of DARK DETAIL mode for RED-EVF

• Addition of SYNCED or FIXED refresh rates for RED-EVF in SYSTEM/MONITOR.

• Addition of RECORD MODE parameter (NORMAL / VARISPEED / TIMELAPSE) in SETUP.

• Addition of enable checkbox for USER 1 and USER 2 keys in KEYMAP submenu.

• Addition of VARIABLE fan speed mode to SYSTEM/SETUP/MAINTANCE/FAN.

Known firmware restrictions for Build 10, RED ONE v 1.6.4

• 4K recording is not yet supported by RED ALERT or by QuickTime Player.

• 4K _H, _M and _P QuickTimes created by camera crash QuickTime Player.

• RED-LCD plus Preview HD-SDI monitor output simultaneously active not supported.

• RED-EVF, RED-LCD, Preview HD-SDI, HDMI simultaneously active not yet supported.

• Frame rate ramping is not supported in this release.

• Intervalometer based Timelapse recording is in the menus but not yet enabled.

• Varispeed recording must first be enabled in SYSTEM/SETUP/RECORD MODE

• Open Gate function in VIDEO/AV MENU/VIEWFINDER is not operational

• Incorrect timecode displayed by QuickTime Player using QuickTime reference movies created by camera when in 50.00 and 59.95 Project Frame Rates

• Project Frame Rate at 29.97 for 4K and 4K 2:1 record is not operational

• Audio recording, monitoring or playback are not supported in this release.

• Dual Link HD-SDI outputs always replicate 720p PREVIEW or PLAYBACK HD-SDI signal.

• Not all frame guides selectable within each record resolution are enabled.

• RGB Channel Exposure Meter viewed on HDMI monitor may exhibit erratic behavior.

• Cannot reset Hours / Minutes / Seconds in TIMECODE menus.

• Possibility of n/a being reported as P.I.N number on boot up.

Other notes:

• On cameras 1 – 50 the stenciling for the four DIN connectors that provide dual link HD-SDI, Preview HD-SDI and Genlock outputs is incorrect. These should be dual link HD-SDI at the top left / top right, Preview HD-SDI at the lower left and Genlock at the lower right.

• 4K (16:9) recording is enabled in this build, and is supported by REDCINE on both Macintosh OSX and Windows XP platforms. At the time of this software release, 4K QuickTime reference movies created by the camera will crash QuickTime Player and RED ALERT is not compatible with 4K (16:9) recordings. Therefore treat with due caution, especially for commercial jobs.

Copyright © 2007 RED Digital Cinema, All Rights Reserved.

---

BETA Build 9 (v1.5.1)
Release Date: 2007-11-06
Download

BETA Build 9, RED ONE camera firmware v1.5.1 Nov 02, 2007

SUMMARY:

New Items: Clip Playback via RED-EVF, RED-LCD, PREVIEW or HDMI monitor outputs. Simple Exposure Meter, Enhanced Focus Assist, Enhanced False Color Mapping. Various debug issues – Record from Play, Adjustable Focus Assist Bar etc.

Installation Instructions for Build 9, RED ONE camera firmware v1.5.1

• Click on the 1.5.1 firmware download link at www.red.com/support web site

• Verify the folder " build_9_red_one_v1.5.1 " appears on your desktop

• Follow the instructions contained in the " build_9_red_one_v1.5.1_readme " file included in that folder.
• On power up, verify the camera rear status reports back: PIN (n/a or value specific to camera) Build 9 Version 1.5.1

• Installation is now complete.

Bug fixes since BETA Build 9, RED ONE v1.5.0

• Removed Image Analysis from Playback mode to prevent camera lock-up

• Pressing RECORD while in Playback forces an immediate clip Record

• Removed Auto Contrast Mode from RED-EVF.

• Focus Assist Bar location is adjustable from Joystick

Significant changes since Build 8, RED ONE v1.3.5 released Oct 18, 2007

• Playback of recorded clips on camera.

• Cue to beginning of existing clips, step through recorded clip list

• Normal, Fast Forward and Reverse playback.

• Addition of Simple Exposure Meter – indicates clipping in R G B channels

• Enhanced Focus Assist Algorithm with adjustable sample window

• Enhanced False Color Exposure Meter with new Skin Tone indication (Pink band)

• Toggle of METERS ON/OFF by User Key of RED-EVF

• Toggle of COLOR ON/OFF by User Key of RED-EVF

• Simplified VIEWFINDER menu structure.

• Change to project logic. Change of Resolution no longer forces New Project.

• Improved Accuracy of Time Code when not in Jam Sync (external reference) mode

• Fixed Edge Code reporting as 1.00.00.000 on power cycle

• Camera log file created on media unmount

• PIN, Build and Version data reported on request in status display

• Use hour meter data reported on request in status display

Known firmware restrictions for Build 9, RED ONE v 1.5.1

• Clips recorded on other cameras or with earlier builds may not play back

• Histograms scale incorrectly when a percentage of pixels clip.

• 4K recording is not yet supported by RED ALERT or by QuickTime Player.

• 4K _H, _M and _P QuickTime files created by camera crash QuickTime Player.

• Two or more monitor outputs simultaneously active is not yet supported.

• Frame rate ramping is not supported in this release.

• TimeLapse is not supported in this release.

• Audio is not supported in this release.

• Dual LInk HD-SDI outputs always replicate PREVIEW HD-SDI signal.

• Not all frame guides selectable in each record resolution are enabled.

• Scaling of waveform meters is not optimized (preliminary implementation)

• Possibility of n/a being reported as P.I.N number on boot up.

Other notes:

• On cameras 1 – 50 the stenciling for the four DIN connectors that provide dual link HD-SDI, Preview HD-SDI and Genlock outputs is incorrect. These should be dual link HD-SDI at the top left / top right, Preview HD-SDI at the lower left and Genlock at the lower right.

• 4K (16:9 aspect ratio) recording is enabled in this build, however RED ALERT playback software is yet available for 4K (16:9) Therefore treat with due caution, this recording mode is not recommended for commercial jobs. 4K QuickTime reference movies are created by the camera, these permit in-field review of the clips until such time as an updated RED ALERT is available.

Copyright © 2007 RED Digital Cinema, All Rights Reserved.